Deal of the WEEK!!!!
Finned Coil Covers!
$59.95 pr!
in the Valve Cover Page
and
2008 Mustang GT engine
$2195.00 in the engine page!
Phone 734-422-8510
email sn95guy@msn.com
For some parts interchange tips, see out new "Parts Interchange" Page
click on pictures to enlarge
Brand
4.6 32valve Carburetor
Adaptor Manifold
(patent pending!)
$459.00 #KK9424AM
recommended 289/302 gaskets are Mr. Gasket #5834 self sealing
adapts 1999-2004 32valve cylinder heads to carburetion by bolting on any vintage 289/302 induction system!
Note: does not fit 1993-1995 Mark Vlll heads at this time
However will fit 1997-98 Mark Vlll single port style heads similar to 99/04 Cobra
fits heads with this style port only
click
picture on left
Pictures below show 289/302 manifold systems installed on the Kar Kraft Adaptor Manifold shown above #KK9424AM
click on pictures to enlarge
6V 8V Weber 4V
*289/302 manifold systems not included with adaptor manifold
* Completed 4.6 DOHC engines using our adaptor manifold above and various 289/302 Ford intake manifold and carburetors.
DOHC 4.6 engines compatible for carburetion are: 1999/01 Cobra, 2003/04 Marauder, 2002/05 Aviator and 2003/04 Mach 1.
Wanna hear a 4.6 DOHC modular engine run with 289 Cobra Webers using our Kar Kraft adaptor manifold above?
give the page a minute to load. enjoy!
*note: Kar Kraft alternator relocation kit, Kar Kraft idler pulley kit and Kar Kraft oil/water block adaptor must be used when installing the adaptor manifold. Parts listed below. * does not fit earlier 1993-1998 4valve heads or any 2V heads.
Brand
5.4 32valve Single Quad 4V Intake Manifold
(patent pending)
to be used with modified 99/03 5.4 32valve lower
$399.00 #KK9424LN4 (upper manifold only)
*includes hardware and intermediate gasket
Brand
Complete 5.4 DOHC single 4V Carb upper and lower manifold system with 750cfm carb, braided fuel line, fuel pressure gage and billet aluminum throttle cable bracket
$1395.00 #KK9424LN4CS
complete system ready to install!
Brand
5.4 32valve Dual Quad 8V Intake Manifold
(patent pending)
to be used with modified 99/04 5.4 32valve lower
$449.00 #KK9424LN8 (upper manifold only)
*includes hardware and intermediate gasket
Brand
Complete 5.4 DOHC dual 4V Carb upper and lower manifold system with 2-600cfm carbs, braided fuel line, fuel pressure gage, secondary vacuum balance diaphragm covers & dual quad linkage
$1595.00 #KK9424LN8CS
complete system ready to install!
Brand
4.6 4valve 671 Blower Manifold!
Adapts the GMC 671 to the 2003 S/C Cobra
factory Intake Manifold!
Machined Billet Aluminum
$899.95 #KK9424671
Has provision underneath for factory 2003/04 Cobra inner
cooler 
*pictured at left is a 2003 Cobra engine with GMC 671 Blower
using our adaptor manifold above.
289/302
Weber Carburetor/Manifold Kit
complete with 4 new 44IDF Weber carbs, new cast aluminum manifold with front integral thermostat housing design, carb linkage, rubber fuel lines, jet kit, tuning manual and synchrometer.
$2,395.00 #KK9430WMK
*pictured with braided fuel line- add $149.00 add $109.95 for screen filter kit
4.6 2valve Carbureted Intake Manifold!
fits 4.6 2valve Power Improved (P.I.) Heads
accepts Holley 4barrel carburetor
$329.95 #KK94242V
add our MSD/Kar Kraft Ignition system below to convert your 4.6 2valve fuel injected engine to a carbureted version! just add your own Holley carb! no other computer or electronics needed!
*pictured above is a completed 2valve engine with 2V carbureted manifold installed
Brand
4.6 Modular Bell housing for C4 Automatic Trans!
bolt the incredible vintage C4 to the new 4.6!
$469.95 #KK7012C4
3/8" thick!
4.6 and 5.4 4valve Header Flanges
Fits 1996-2005 32valve heads. Complete w/matching gaskets
*note-does not fit Cobra R, Ford GT or 2007/08 5.4 SVT heads
$89.95 pr. #KK9430HF
Brand
4.6 or 5.4 Oil/Water Block Adaptor!
accepts AN fittings for remote oil filter or oil cooler
has OEM radiator hose outlet
$119.00
#KK6066
*perfect for street rods and race cars! Mandatory when relocating the alternator to the side of the block and using Kar Kraft carburetor adaptor manifold!
Brand
Alternator Relocation Kit
positions alternator down on L.H. side of block
includes cast aluminum bracket, alternator and hardware
$279.95 #KK13800
* 3 pin connector is different on this alternator. must be re-wired or connector changed when used in Mustang or Cobra applications
*must be used with Kar Kraft Adaptor Manifold above. perfect for race car applications with modified intakes! NOTE: frame rail clearance issues may arise on some vehicles on driver's side. Late model mustang and cobra models may have to modify alternator mounting surface to clear brake lines.
Brand
4.6 4V Alternator Idler Pulley and Bracket
installs in original factory alternator position
$89.95 #KK13801
Brand
4.6 2V and 4V Power Steering Delete
includes bracket, pulley and spindle
installs in factory P.S. position to side of block
$89.95
#KK3601PSD
* does not fit 03/04 S/C Cobra
MSD/Kar Kraft Ignition System
fits all 4.6 2valve or 4valve engines!
no other computer or electronics needed to carburet your modular engine when converting to carburetion! Plug and Play!
plugs in to all factory sensors!
MSD/Kar Kraft Ignition + 12volts= RPM! That simple!
complete with brain box, harness, map sensor & instructions
$399.95 #KK12300MES
no computer or electronics degree required!
Application: 1999 and newer coil over plug engines only
* note: for those of you who are computer friendly, the MSD/Kar Kraft Ignition System includes a serial port and software for custom tuning the timing and spark curve depending on your application.
*Caution- the MSD/Kar Kraft Ignition System comes pre-wired for a 2valve application. when using on a 4valve engine, the wires at each coil connection must be reversed before firing. 2valve engines and 4valve engines have reverse polarity at the coils.
All Electrical Components are not returnable
email sn95guy@msn.com